Phoenix Bluetooth seriële poortadapter Manual download pdf

7749_de_00

AUTOMATION

BLUETOOTH AT COMMAND LIST

Data Sheet

1Description

The FL BLUETOOTH Serial Port Adapter (BT SPA) is a se-

rial Bluetooth device that is suitable for industrial use. BT

SPA supports Bluetooth specification 2.0 and has one 9-

pos. D-SUB port and one Bluetooth radio interface.

A software tool is available for programming support, which

visualizes the key settings. Various tabs can be used to se-

lect the settings, which are then transmitted to the device via

AT commands. Two BT SPAs can be paired in a point-to-

point connection (P2P).

Another option is to connect a Bluetooth access point to a

BT SPA. In this case the Bluetooth connection is establis-

hed via a Bluetooth access point. The Bluetooth access

point web page (WBM) can now be used to adjust the mo-

dule settings via AT commands.

The AT commands described below are used to configure

the BT SPA. They can be used to read the settings in the re-

levant BT SPA or to modify the relevant settings.

The AT commands can be transmitted to the module via:

– A serial connection

– An existing Bluetooth connection

2 Supported Bluetooth profile - Serial

Port Profile (SPP)

The SPP Bluetooth profile can be used to establish a serial

connection between two Bluetooth devices.

The Serial Port Adapter can be in two different modes AT

mode and data mode Some serial port adapter models also

support the ECI mode, which is not covered in this docu-

ment.. The Serial Port Adapter starts up in data mode and

can be requested to move to AT mode by sending an es-

cape sequence. The default escape sequence consists of

three consecutive forward slash characters ‘/’. The escape

sequence character can be changed using the ATS2 com-

mand. Pressing the restore-button on the Serial Port Adap-

ter, when it is powered up, restores the default escape cha-

racter.

The following criteria must be met for the Serial Port Adapter

to interpret the sequence as a valid escape sequence:

– Before the escape sequence there must be silence for

1 second. This time can be changed using the

AT*AMET command.

Note: Operation of the wireless system is permitted only when using accessories available from Phoenix Contact.

The use of other accessory components invalidates the approval of operation.

Make sure you always use the latest documentation. It can be downloaded at

www.download.phoenixcontact.com

List of available AT commands for serial Bluetooth

devices

1 2 3 4 5 6 ... 42 43

Summary of Contents

Page 1 - BLUETOOTH AT COMMAND LIST

Page 2

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 10Bond (AT*AGB=)Un_Bond (AT*AGUB=)AT Command DescriptionAT*AGB=<bd_addr><CR> Performs

Page 3 - 4 AT Commands Reference

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 11Read_Bonded_Devices (AT*AGBD?)Read_Fixed_PIN (AT*AGFP?)AT Command DescriptionAT*AGBD?<CR>

Page 4 - 7749_de_00 PHOENIX CONTACT 4

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 12Write_Fixed_PIN (AT*AGFP=)Read_Local_Name (AT*AGLN?)Write_Local_Name (AT*AGLN=)AT Command Descri

Page 5

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 13Read_Local_COD (AT*AGLC?)Responses Description<CR><LF>OK<CR><LF> Success

Page 6 - 7749_de_00 PHOENIX CONTACT 6

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 14Write_Local_COD (AT*AGLC=)Get_MasterSlaveRole (AT*AGGMSR=)AT Command DescriptionAT*AGLC=<cod&

Page 7

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 15Change_MasterSlaveRole (AT*AGCMSR=)Read_MasterSlaveRole_Policy (AT*AGMSP?)AT Command Description

Page 8 - 7749_de_00 PHOENIX CONTACT 8

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 16Write_MasterSlaveRole_Policy (AT*AGMSP=)Get_RSSI (AT*AGRSS=)AT Command DescriptionAT*AGMSP=<r

Page 9

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 176 Service Search CommandsService_Search (AT*ARSS=)AT Command DescriptionAT*ARSS=<bd_addr>,

Page 10 - 7749_de_00 PHOENIX CONTACT 10

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 187 Data Mode CommandsData_Mode (AT*ADDM)service_description_valid enumerator 0: The service_descr

Page 11

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 19Connect_To_Serial_Service_Data_Mode (AT*ADCP=)Close_Serial_Connection_Data_Mode (AT*ADCC=)AT Com

Page 12 - 7749_de_00 PHOENIX CONTACT 12

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 2– After the escape sequence there must be silence for 1 second. This time can be changed using th

Page 13

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 20Read_Default_Client_Profile (AT*ADDCP?)Write_Default_Client_Profile (AT*ADDCP=)Responses Descrip

Page 14 - 7749_de_00 PHOENIX CONTACT 14

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 21Read_Default_Server_Profile (AT*ADDSP?)Write_Default_Server_Profile (AT*ADDSP=)Module Constraint

Page 15

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 22Read_Max_No_Of_Remote_Peers (AT*ADMRP?)Read_No_Of_Remote_Peers (AT*ADNRP?)Responses Description&

Page 16 - 7749_de_00 PHOENIX CONTACT 16

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 23Write_No_Of_Remote_Peers (AT*ADNRP=)Read_Default_Remote_Peer (AT*ADRDRP=)AT Command DescriptionA

Page 17

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 24Response Parameters Type Valuebd_addr Bd_Addr Bluetooth device address of the default remote pee

Page 18 - 7 Data Mode Commands

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 25Write_Default_Remote_Peer (AT*ADWDRP=)Read_Inactivity_Tick (AT*ADIT?)AT Command DescriptionAT*AD

Page 19 - 7749_de_00 PHOENIX CONTACT 19

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 26Write_Inactivity_Tick (AT*ADIT=)Module ConstraintFL BT SPA Not supported.Instead use the watchdo

Page 20 - 7749_de_00 PHOENIX CONTACT 20

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 27Read_Wireless_Multidrop_Configuration (AT*ADWM?)AT Command DescriptionAT*ADWM?<CR> This re

Page 21

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 28Write_Wireless_Multidrop_Configuration (AT*ADWM=)8 Informational CommandsRead_Local_BD_ADDR (AT*

Page 22 - 7749_de_00 PHOENIX CONTACT 22

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 299 Miscellaneous CommandsRead_RS232_Settings (AT*AMRS?)Response Parameters Type Valuemanufacturer

Page 23

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 3ample, the Bluetooth Device Address 0x112233AABBCC is represented as 112233AABBCC or 112233aabbcc

Page 24 - 7749_de_00 PHOENIX CONTACT 24

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 30Write_RS232_Settings (AT*AMRS=)stop_bits enumerator 1: 1 stop bit (default value)2: 2 stop bitsp

Page 25

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 31Read_Serial_Interface_Type (AT*AMSIT?)Write_Serial_Interface_Type (AT*AMSIT=)Read_Allow_Configur

Page 26 - 7749_de_00 PHOENIX CONTACT 26

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 32Write_Allow_Configuration_Over_Bluetooth (AT*ACCB=)Read_Controller_Power_Save_Mode (AT*AMPM?)Res

Page 27

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 33Write_Controller_Power_Save_Mode (AT*AMPM=)Read_Max_Output_Power (AT*AMMP?)AT Command Descriptio

Page 28 - 8 Informational Commands

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 34Write_Max_Output_Power (AT*AMMP=)Read_Esc_Sequence_Timing (AT*AMET?)AT Command DescriptionAT*AMM

Page 29 - 9 Miscellaneous Commands

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 35Write_Esc_Sequence_Timing (AT*AMET=)Read_Watchdog_Settings (AT*AMWS?)AT Command DescriptionAT*AM

Page 30 - 7749_de_00 PHOENIX CONTACT 30

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 36Write_Watchdog_Settings (AT*AMWS=)bt_connect_timeout integer Max connection time in seconds befo

Page 31

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 37Read_DTR_DSR_Settings (AT*AMDS?)Write_DTR_DSR_Settings (AT*AMDS=)AT Command DescriptionAT*AMDS?&

Page 32 - 7749_de_00 PHOENIX CONTACT 32

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 38Read_Link_Policy (AT*AMLP?)Write_Link_Policy (AT*AMLP=)AT Command DescriptionAT*AMLP?<CR>

Page 33

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 39Response Parameters Type Valuelink_policy integer Link policy configurations:0: Default, No sni

Page 34 - 7749_de_00 PHOENIX CONTACT 34

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 4Command “ATS2”Command “ATE”Module ConstraintFL BT SPA The Store_Factory_Settings are not availabl

Page 35

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 40parameter integer This parameter has different meaning for different link policies.Link policies

Page 36 - 7749_de_00 PHOENIX CONTACT 36

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 41Read_Feature_Mask (AT*AMRFM=)Write_Feature_Mask (AT*AMWFM=)Responses Description<CR><LF

Page 37

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 42Read_Channel_Map (AT*AMCM?)Write_Channel_Map (AT*AMCM=)Responses Description<CR><LF>

Page 38 - 7749_de_00 PHOENIX CONTACT 38

BLUETOOTH AT COMMAND LIST7749_de_00 43PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00 PHOENIX CONTACT • P.O.Bo

Page 39

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 55 GAP Commands5.1 Read_Discoverability_Mode (AT*AGDM?)Write_Discoverability_Mode (AT*AGDM=)AT Com

Page 40

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 6Read_Connectability_Mode (AT*AGCM?)Write_Connectability_Mode (AT*AGCM=)Read_Pairing_Mode (AT*AGPM

Page 41 - 7749_de_00 PHOENIX CONTACT 41

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 7Write_Pairing_Mode (AT*AGPM=)Read_Security_Mode (AT*AGSM?)Write_Security_Mode (AT*AGSM=)AT Comman

Page 42

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 8Name_Discovery (AT*AGND=)Device_Discovery (AT*AGDD=)Responses Description<CR><LF>OK&l

Page 43 - 7749_de_00 43

BLUETOOTH AT COMMAND LIST7749_de_00 PHOENIX CONTACT 9Inquiry (AT*AGI=)Response Parameters Type Valueno_of_devices integer Value in range {0..255}.Numb

Comments to this Manuals

No comments

Phoenix Bluetooth seriële poortadapter Manual

Browse online or download Manual for Network switches Phoenix Bluetooth seriële poortadapter. Phoenix Bluetooth seriële poortadapter User Manual

Summary of Contents

Comments to this Manuals